I know this has been discussed in the past, but thought I'd ask again to see how people are cleaning their cameras sensors.
I'm worried about causing damage so have paid to have mine cleaned, however the last time I did so I was disappointed as it wasn't really very clean. So I'm now looking at other options as mine really does need a clean.
Thanks
Chris
Funny you should say this - I sent mine off to Canon for a service, clean and AF check - I'm a CPS member and they have changed how membership levels are calculated so I've gone back to being a Gold member - which means a 3day turnaround - which almost worked but I didn't get the payment to them today to get it out tonight, so won't be back until Tuesday.
Not the cheapest option, but figure its the 1st time its been done in 4 years and I don't know how many shots - a fair few though! (£117 inc vat, carriage both ways)
I've got a cleaning kit from Just - had it years, rarely used. Sensor cleaning is really easy when it is required, but I haven't had to clean one for more than 2 years. The kits still seem to be available on Amazon for about £24.
I clean sensors regularly. Normally just a blow with a rocketblower (Giotto, big blower has filter in it). I have used the arctic butterfly but was not pleased with this at all.The brush becomes static and attract the dust from the sensor alright, but if you get too close to the bottom of the sensor it takes all the dust from the dust glue strip and smears it over the sensor making things worse. grease spots I remove with a swab. I hardly ever have to use that anymore, because my camera's are old and well used so the grease that would be a problem is all gone.
Rocket blower for me is the best! I have to use it quite often because I change lenses often.
I set my Pentax to clean the sensor dust by vibrating it during switch off (rather than the default option - during switch on - which makes the camera longer to start up). And on the very few occasions I've noticed a dust spot a rocket blower has easily shifted it. So I've never required swabs etc but I would be quite apprehensive about using one.
I do change lenses often, but very seldom anywhere except indoors. When I must do it outside I'm very careful to find a dust free and wind free shelter.
Simon
I have done my previous cameras with swabs - but I wanted it serviced anyway.
Rocket blower did nothing.
I change lenses all the time, so inevitably get dust and muck in - but suspect some is the oil off the mechanism.
I'm sure most of the dust on your camera comes from the camera it's self. Think gears grinding against each other. :o
And a flappy shutter at 12fps :)
Thanks for the replies guys. Sounds like I shouldn't be too worried about it and think I'll try first with my rocket blower. I do change lenses regularly and perhaps should be more careful when doing so.
Will try over the weekend and see how it goes.
Thanks again.
Late to the party but I`m another that does it myself with fluid and swabs. I firs try my rocket blower, then my arctic butterfly keeping well away from the edge and finally if not resolved give it a wet clean. the only time I paid to have it cleaned locally it wasn`t done properly and I had to leave it in the shop to have it done again FOC. As oldboy said no matter how carefully you change lenses it will happen. Some of it is internal dust / bits relocating, other bits drawn in. I often wonder how effective the rocket blower can be even done correctly with the camera upside down as we`re merely blowing it from place to place.
Well I used my rocket blower but sensor is still pretty dirty. Think I'll have to try swabs and see how that goes.
Strangely though, I can't see the dirty spots when I shoot video.
Probably not stopped down far enough?
I'm another who uses a blower (only twice); the first time I noticed a dust spot was when using a slide duplicator with its own small aperture lens. If I need to check carefully, I have a 135mm lens that stops down to f/32.
Edit to add - late reply as I've been on holiday.
Mine came back fully serviced, cleaned all over, inside and out, and AF checked. Ready for next week at Le Mans and the USA in October.
A bit late, but another vote for DIY.
I usually use a rocket blower or arctic butterfly, but a couple of weeks ago, it got to the stage where they weren't good enough.
10 mins with a swab (and very shaky hands - I was nervous) all done and I'd be quite happy to do it again now.
That's reassuring to hear. Think I'll have to give it a go. And if I get it badly wrong it means I get a new camera. So it's a win win really.
Quote from: anglefire on September 01, 2018, 11:53:28 PM
Mine came back fully serviced, cleaned all over, inside and out, and AF checked. Ready for next week at Le Mans and the USA in October.
Sounds like a good trip.
I have a friend, well acquaintance who races for Corvette in the ALMS.
Le Mans is with work - we sponsor a car - the one currently on the front page! But the french have refused to let the class race -probably because they loose! - but we are still going! Half of them only go for the drink anyway, so makes little difference!
I went in 2016 for the 24Hours Classic - which was good, though this time will be the short circuit (I assume!)
Quote from: Jediboy on September 02, 2018, 12:52:17 PM
That's reassuring to hear. Think I'll have to give it a go. And if I get it badly wrong it means I get a new camera. So it's a win win really.
;D
Quote from: anglefire on September 02, 2018, 01:20:06 PM
Le Mans is with work - we sponsor a car - the one currently on the front page! But the french have refused to let the class race -probably because they loose! - but we are still going! Half of them only go for the drink anyway, so makes little difference!
I went in 2016 for the 24Hours Classic - which was good, though this time will be the short circuit (I assume!)
It'll be a great weekend I'm sure. Enjoy.